Hot Tub Chemistry for Beginners
A hot tub holds a few hundred gallons of hot water shared by several people, so it needs more attention than a pool, but less chemistry than most shop shelves suggest. You need to manage three things: sanitiser, pH, and when to change the water.
Safety: the US Consumer Product Safety Commission says hot tub water should never be hotter than 104 °F (40 °C), and treats 100 °F as safe for a healthy adult. Keep young children out of hot water, and ask a doctor first if you are pregnant.
The levels that matter
| Test | Target | Source |
|---|---|---|
| Free chlorine | At least 3 ppm | US CDC, for home hot tubs |
| Bromine (if you use bromine instead) | At least 4 ppm | Public spa standard (APSP-11), used in many state codes |
| pH | 7.0–7.8 | US CDC |
| Total alkalinity | Commonly 80–120 ppm | Typical spa-maker guidance; check your tub’s manual |
| Temperature | No higher than 104 °F | US CPSC |
The CDC advises testing chlorine and pH at least twice a day in a hot tub, and more often when it is busy. At the very least, test before every soak. Hot water and several bathers can use up sanitiser in hours.
How much chlorine to add
Doses are tiny because the water volume is small. Here is what raises free chlorine by 3 ppm in a 400-gallon tub:
| Product | Amount for +3 ppm | Side effect |
|---|---|---|
| Liquid chlorine 12.5% | 1.3 fl oz | None that builds up |
| Unscented bleach 6% | 2.7 fl oz | None that builds up |
| Dichlor granules 56% | 8.1 g (0.29 oz) | +2.7 ppm stabilizer (CYA) each time |
Not sure of your volume? The manual lists it, or use the volume calculator. For other amounts or products, put your tub’s gallons into the chlorine calculator.
The dichlor trap
Dichlor is the granule most spa shops sell, because it dissolves fast and is easy to measure. It also carries stabilizer (cyanuric acid, CYA), and stabilizer never gets used up. It only leaves when you drain water.
Say your tub uses 3 ppm of chlorine a day and you replace it with dichlor. Each day adds 2.7 ppm of stabilizer, so after 30 days the water holds about 81 ppm. The more stabilizer there is, the more slowly chlorine kills germs, and in a hot tub that is a real health issue. That is why the CDC recommends not using cyanuric acid, or chlorine products that contain it, in hot tubs.
If you use dichlor anyway, the safest habit is to change the water more often. Otherwise, use liquid chlorine or plain unscented bleach for routine dosing.
Keeping pH in range
Hot tub pH tends to drift up, because the jets and air blowers drive carbon dioxide out of the water. High pH weakens chlorine and can cloud the water and scale the heater. Doses are small: in our 400-gallon example, bringing pH from 7.9 down to 7.5 at alkalinity 80 ppm takes only about 0.43 oz (12.1 g) of dry acid. Add less than you think, wait 30 minutes with the jets running, and retest. The pH & alkalinity calculator works for tubs as well as pools.
A simple routine
- Before every soak: test sanitiser and pH. Add chlorine (or bromine) if it is below target.
- After every soak: add a little sanitiser to cover what the bathers used up, with the jets running and the cover open so fumes can escape.
- Weekly: test alkalinity, rinse the filter, and check the temperature with a separate thermometer.
- On schedule: drain, clean and refill (see below).
Add one chemical at a time, with the jets running, and let it circulate before adding the next. Never mix chemicals together.
When to change the water
Every soak leaves sweat, oils and soap residue in the water, and in a small tub they build up fast. Hot tub makers use a simple rule of thumb: gallons ÷ 3 ÷ average daily bathers = days between water changes. For a 400-gallon tub with 2 bathers a day, that is 400 ÷ 3 ÷ 2 ≈ 67 days. Change it sooner if the water foams, smells, stays cloudy, or won’t hold sanitiser.
Frequently asked questions
Chlorine or bromine: which is better for a hot tub?
Both work, as long as you keep them at the right level: at least 3 ppm for chlorine, at least 4 ppm for bromine. Bromine is popular in hot tubs; chlorine is usually cheaper and easier to find. Pick one and stick with it. Chlorine added to a bromine tub reacts with the bromide in the water and turns into bromine, which makes test results confusing.
How often should I add chemicals to my hot tub?
Test before every soak, and add sanitiser whenever it is below your target. A busy tub may need chlorine every day; a tub used once a week may need a top-up only after each use. The test kit, not the calendar, tells you when.
Why does my hot tub water foam?
Foam usually comes from lotions, soaps, laundry detergent left in swimsuits and body oils building up in a small volume of water. A defoamer hides it for a while. Rinsing off before soaking helps, and if foam keeps returning, the water is due for a change.
Can I use pool chemicals in a hot tub?
Many are the same chemicals, but doses are tiny in a hot tub, so pool-sized scoops and tablets are easy to overdo. Measure carefully, use products labelled for spas where you can, and follow the label.
Sources
- Free chlorine at least 3 ppm in hot tubs, pH 7.0–7.8, testing at least twice a day, and the recommendation not to use cyanuric acid or products containing it in hot tubs (US CDC, home pool and hot tub water treatment and testing).
- Hot tub water should never exceed 104 °F; 100 °F is considered safe for a healthy adult (US Consumer Product Safety Commission, “CPSC warns of hot tub temperatures”).
- Minimum spa bromine residual of 4.0 ppm in the APSP-11 water quality standard, aligned with the Model Aquatic Health Code (Pool & Spa News); also used in state spa codes such as Washington’s.
- Water-change rule: gallons ÷ 3 ÷ daily bathers (Jacuzzi, “How often to change hot tub water”).
- Doses calculated with the same tested formulas as our chlorine and pH calculators.