Home › Pool salt calculator
Pool Salt Calculator
Enter your pool size and your current salt reading. You get the pounds (or kilograms) and the number of bags to add, or how much water to replace if you are over target.
Check your generator’s manual for its exact target. Most makers say to switch the cell off while new salt dissolves and to run the pump until the salt is fully mixed (often about 24 hours) before you retest. It is easy to add more salt later and hard to remove it, so if in doubt add about three-quarters, wait, and retest.
How the calculation works
Salt level is measured in parts per million (ppm): milligrams of salt per litre of water. One US gallon of water weighs about 8.345 lb, so:
Pounds of salt = gallons × 8.345 × (target ppm − current ppm) ÷ 1,000,000
In metric it is simpler, because a litre of water weighs about a kilogram: kg of salt = litres × (target − current) ÷ 1,000,000.
Worked example
A 12,000-gallon pool reads 1,200 ppm and you want 3,200 ppm:
- Increase needed = 3,200 − 1,200 = 2,000 ppm
- Salt = 12,000 × 8.345 × 2,000 ÷ 1,000,000 = 200.3 lb
- 40 lb bags = 200.3 ÷ 40 = 5.01 → 5 full bags. The extra 0.3 lb is too small to matter, so don’t open a sixth bag: a whole extra 40 lb would push this pool about 400 ppm over target, to roughly 3,600 ppm.
When the salt is too high
The only way down is dilution. The share of water to replace is 1 − (target ÷ current). A 15,000-gallon pool at 4,000 ppm with a 3,200 target needs 1 − 0.8 = 20% replaced, which is 3,000 gallons.
Pool salt chart (pounds to reach 3,200 ppm)
| Pool size | From 0 ppm | From 1,000 ppm | From 2,000 ppm | From 2,500 ppm | From 3,000 ppm |
|---|---|---|---|---|---|
| 5,000 gal | 134 lb | 92 lb | 50 lb | 29 lb | 8 lb |
| 10,000 gal | 267 lb | 184 lb | 100 lb | 58 lb | 17 lb |
| 15,000 gal | 401 lb | 275 lb | 150 lb | 88 lb | 25 lb |
| 20,000 gal | 534 lb | 367 lb | 200 lb | 117 lb | 33 lb |
| 25,000 gal | 668 lb | 459 lb | 250 lb | 146 lb | 42 lb |
| 30,000 gal | 801 lb | 551 lb | 300 lb | 175 lb | 50 lb |
| 40,000 gal | 1,068 lb | 734 lb | 401 lb | 234 lb | 67 lb |
How to add salt to your pool
- Test the salt level with a salt test strip or digital meter, not just the generator display.
- Work out the dose above. Switch the generator off as your manual directs.
- With the pump running, pour the salt around the shallow end, away from the skimmer.
- Brush the salt toward the deep end so it does not sit on the floor.
- Run the pump until it has fully dissolved and mixed, then retest before adding more.
Frequently asked questions
What salt level should my pool be?
Most salt chlorine generators run between about 2,700 and 3,400 ppm, and 3,200 ppm is the most common target. Your generator’s manual is the authority: some models want a different range, and running outside it can stop chlorine production or throw a fault.
How many 40 lb bags of salt do I need for a new salt pool?
Starting from 0 ppm and aiming for 3,200 ppm, you need about 2.67 lb of salt per 100 gallons, so roughly one 40 lb bag per 1,500 gallons. A 15,000-gallon pool needs about 400 lb, which is 10 bags.
I added too much salt. What now?
Salt does not evaporate or get used up quickly, so the only fix is dilution: drain part of the water and refill with fresh water. Enter your current reading above your target and the calculator tells you how many gallons to replace.
Can I use table salt or water-softener salt?
Use salt sold as pool salt, or plain sodium chloride that is at least 99% pure with no iodine, anti-caking agents or added minerals. Additives can stain surfaces and cloud the water. Check the bag before you buy.
Why does my generator show a different salt reading than my test strip?
Generator readings drift as the cell ages or gets scale on it, and depend on water temperature. Confirm with a dedicated salt test (strips or a digital meter) before adding a large amount.
Sources
- Definition of ppm (mg per litre) and the mass of water: about 8.345 lb per US gallon at typical pool temperatures.
- Typical salt range of 2,700–3,400 ppm with 3,200 ppm as the common target, as stated by Omni Calculator and Swim University; always defer to your generator manufacturer’s manual.
- Results checked against published worked examples: 10,000 gal from 0 to 3,200 ppm = 267 lb (Swim University); 1 lb raises 120,000 gal by 1 ppm (The Pool Nerd); 100 gal at 4,000 ppm needs 20 gal replaced for 3,200 ppm (Omni Calculator).