Home › Pool pH & alkalinity calculator

Pool pH & Alkalinity Calculator

How much muriatic acid, dry acid, baking soda or soda ash to add. Unlike “ounces per 0.2 pH” rules, this calculator accounts for your alkalinity and stabilizer, and shows where your pH and alkalinity should land afterwards.

By Engr. Nasir Naseer Khan · Reviewed 2026-11-17

What do you want to change?

—

Acid safety: wear gloves and eye protection. Add acid to water, never water to acid: pre-dilute it in a plastic bucket of pool water, then pour slowly into the deep end with the pump running. Never mix acid with chlorine, because together they release toxic chlorine gas. Add about three-quarters of the dose, wait 4–6 hours, and retest before adding the rest.

Recommended ranges

Quick reference (10,000 gallons)

ChangeProductAmount
Lower TA by 10 ppmMuriatic acid 31.45%25.6 fl oz
Lower TA by 10 ppmDry acid 93.2%2.1 lb
Raise TA by 10 ppmBaking soda1.4 lb

Why one “ounces per 0.2 pH” rule doesn’t work

Muriatic acid (31.45%) needed to drop 10,000 gallons from pH 7.8 to 7.5, from this calculator’s chemistry model:

Total alkalinity (CYA 30)60 ppm80 ppm100 ppm120 ppm150 ppm
Acid needed6.6 fl oz8.2 fl oz9.8 fl oz11.4 fl oz13.9 fl oz
Stabilizer (TA 100)0 ppm CYA30 ppm CYA50 ppm CYA80 ppm CYA
Acid needed8.1 fl oz9.8 fl oz11.0 fl oz12.7 fl oz

The same 0.3 pH drop needs about twice as much acid at 150 ppm alkalinity as at 60 ppm, and stabilizer adds more on top. That is why fixed rules from different sources disagree so widely.

How the calculation works

Worked example

A 15,000-gallon pool at pH 7.9, TA 110 ppm and CYA 40 ppm, targeting pH 7.5, needs about 20.6 fl oz of 31.45% muriatic acid. Its TA drops to about 105 ppm, because acid always removes some alkalinity.

pH results are estimates. Temperature, borates and test-kit accuracy all move the real answer a little, so add three-quarters, circulate, and retest.

Frequently asked questions

Should I adjust pH or alkalinity first?

Alkalinity first. Total alkalinity is the buffer that holds pH in place, so if it is far out of range, pH keeps drifting no matter how often you correct it. Get TA into range, let the water circulate, then fine-tune pH.

Why does the same pH drop need different amounts of acid in different pools?

Because the acid has to overcome the water’s buffer. Higher total alkalinity and more stabilizer (CYA) both soak up acid, so a pool at TA 120 with 50 ppm CYA needs noticeably more acid than one at TA 80 with no stabilizer. That is why this calculator asks for TA and CYA instead of using a single “ounces per 0.2 pH” rule.

How do I lower alkalinity without crashing pH?

Add acid to bring the pH down to about 7.0–7.2, then aerate the water (run fountains, waterfalls or jets pointed up). Aeration drives off carbon dioxide and raises pH without adding alkalinity back. Repeat until TA reaches your target.

Is pool-store “alkalinity increaser” the same as baking soda?

Yes. Alkalinity increaser is sodium bicarbonate, the same chemical as grocery-store baking soda. Plain baking soda works the same way and usually costs less per pound.

What pH should my pool be?

The US CDC recommends keeping pool and hot tub pH between 7.0 and 7.8. Many owners aim for about 7.4–7.6, which is comfortable for eyes and lets chlorine work well.

Sources