How to Raise pH in a Pool
There are three ways to raise pool pH: soda ash, baking soda, and air. Most guides treat them as interchangeable. They aren’t: each one moves your alkalinity by a very different amount, and picking the wrong one can leave you with a second problem to fix. Check alkalinity first, then choose.
First: test pH and alkalinity together
The US CDC’s range for pool pH is 7.0–7.8, and most owners aim for about 7.4–7.6. Before adding anything, test total alkalinity (TA) too, plus stabilizer (CYA) if you use it, because a TA test counts part of the stabilizer. Your alkalinity decides which fix is right:
| Your alkalinity | Best way to raise pH | Why |
|---|---|---|
| Low (under about 80 ppm) | Baking soda first, then soda ash if pH is still low | Fixes the weak buffer that let pH fall |
| Normal (about 80–110 ppm) | Soda ash | Fast, with a modest alkalinity rise |
| High (about 110 ppm or more) | Aeration | Raises pH without adding any alkalinity |
Soda ash: the main pH raiser
Soda ash (sodium carbonate, sold as “pH up” or “pH increaser”) raises pH quickly. It also raises alkalinity, more than many people expect.
Example: a 15,000-gallon pool reads pH 7.0, alkalinity 80 ppm and stabilizer 30 ppm. Bringing it to pH 7.5 takes about 3.1 lb (49 oz) of soda ash, and alkalinity rises to about 103 ppm. That’s still fine, but it shows why soda ash is the wrong choice when alkalinity is already high.
The lower the starting pH, the more it takes. With no stabilizer, going from 6.8 to 7.5 in the same pool needs about 4.8 lb, and alkalinity climbs to about 116 ppm.
Baking soda: for low alkalinity, not low pH
Baking soda (sodium bicarbonate, “alkalinity increaser”) is the right product when alkalinity is low. It is a poor pH raiser. Using it on its own to push pH from 7.0 to 7.5 would take about 36 lb in our example pool and leave alkalinity at about 229 ppm, far too high. Then you would be following our guide to lowering alkalinity.
When both pH and alkalinity are low, use both, in order. If the same pool started at alkalinity 60 ppm:
- Baking soda first: 4.2 lb raises alkalinity from 60 to 80 ppm. pH rises only a little, to about 7.1.
- Retest the next day, then add soda ash for the rest: about 2.1 lb takes pH to 7.5, leaving alkalinity at about 96 ppm.
Aeration: raising pH with nothing but air
Water holds dissolved carbon dioxide, which acts as a weak acid. Stirring the surface lets that CO₂ escape, and as it leaves, pH rises, while alkalinity stays exactly the same. Point return jets up at the surface, run waterfalls or fountains, or use an air pump. It is slower than soda ash and usually takes a day or more, but it is free, and it is the only option that doesn’t add alkalinity. It slows down as pH rises but doesn’t stop at a set point, so check pH daily and stop aerating when you reach your target.
How to add soda ash
- Work out the dose with the pH & alkalinity calculator. It shows the pH and alkalinity you will end up with.
- Add no more than about half the dose at a time. It is easy to overshoot, and pushing pH back down means adding acid.
- Pre-dissolve it in a bucket of pool water (chemical into water, never the reverse), then pour it slowly in front of a return jet with the pump running. Adding a lot at once can turn the water cloudy for a while.
- Wait at least 6 hours (overnight is better), retest, and add the rest if needed.
Why it keeps dropping
If pH falls again within days, look for the cause. Trichlor tablets are acidic and keep pulling pH down. Low alkalinity gives pH nothing to hold on to. Heavy rain dilutes your buffer. Fix the cause, and pH usually stays put.
Frequently asked questions
What causes low pH in a pool?
The usual causes are acidic products and rain. Trichlor tablets and dry acid both push pH down, as does too much muriatic acid, and heavy rain is slightly acidic and dilutes your alkalinity buffer. Low alkalinity makes it worse, because there is less buffer to hold pH steady.
Is low pH dangerous?
Water below pH 7.0 is corrosive. Over time it can etch plaster, corrode metal parts like heater cores and ladders, and sting swimmers’ eyes. It is worth fixing promptly, but it is not an emergency that calls for dumping in chemicals all at once.
How long after adding soda ash can I swim?
Follow the product label. Most labels say you can swim once the product has dissolved and circulated, usually within an hour or so with the pump running. Retest pH before swimming either way.
Does baking soda raise pH?
Only a little. Baking soda mainly raises alkalinity. In our example, adding enough to raise alkalinity by 20 ppm moved pH only from 7.0 to 7.1. Use it when alkalinity is low, and use soda ash or aeration when pH alone is low.
Sources
- pH 7.0–7.8 for pools (US CDC, home pool and hot tub water treatment and testing).
- Carbon dioxide outgassing raises pH with no change in total alkalinity, and aeration speeds it up (Orenda, “CO₂ and pH: Henry’s law”).
- Soda ash raises pH and some alkalinity; baking soda mainly raises alkalinity, with a small pH change (TroubleFreePool, “Soda ash and TA increases for upward pH changes”).
- All doses, end-pH and end-alkalinity values come from our pH & alkalinity calculator’s carbonate model, which is tested against published dose figures.