How to Shock a Pool, Step by Step
“Add a bag of shock every week” is how most pools get shocked. It is also why most shocks either waste chemical or don’t work. Shocking properly starts with a test, uses a dose worked out from your numbers, and ends with a retest.
What shocking actually does
Chlorine in your pool exists in two forms. Free chlorine (FC) is the active sanitiser. Combined chlorine (CC) is chlorine that has already reacted with sweat, urine and other organic waste. It sanitises poorly, irritates eyes, and causes the “chlorine smell” people blame on too much chlorine. It is really a sign of too little.
Shocking means raising free chlorine high enough, fast enough, to destroy those combined compounds and anything else using up your chlorine. The standard target in public-pool practice is breakpoint chlorination: raise free chlorine to 10 times the combined chlorine.
When you should shock
- Your test shows combined chlorine above about 0.5 ppm. Public pools often act at 0.2 ppm.
- The pool smells strongly of chlorine, or swimmers complain of red eyes.
- The water is turning cloudy or green, or the walls feel slimy.
- After a big pool party, a heavy storm, or when you open the pool for the season.
If your free chlorine is steady and combined chlorine is near zero, you don’t need to shock, whatever the calendar says.
What you need
- A test kit that reads both free and total chlorine. Combined chlorine is total minus free, so you need both. A drop-test kit (DPD or FAS-DPD) is more precise than strips.
- A chlorine product. Unstabilized chlorine (liquid chlorine or cal-hypo) is best for shocking, because it doesn’t add stabilizer (CYA) to the water.
- Gloves, eye protection, and a clean plastic bucket used only for pool chemicals.
Step-by-step
- Test free chlorine, total chlorine and pH. Chlorine works much better at lower pH. UK pool guidance (PWTAG) recommends 7.0–7.4, and the US CDC’s range is 7.0–7.8. If your pH is above about 7.6, bring it down first with the pH calculator.
- Work out your target. Combined chlorine = total − free. Breakpoint target = 10 × combined chlorine.
- Work out the dose for your pool size and product with the shock calculator.
- Wait until dusk, so the sun doesn’t burn off the chlorine.
- Add the chlorine with the pump running. Pour liquid chlorine slowly around the edge of the deep end. Pre-dissolve granular shock in a bucket of pool water (chemical into water, never water into chemical) and pour it in. Never mix two chemicals together.
- Brush the walls and floor and let the pump run through the night.
- Retest in the morning. If combined chlorine is still above 0.5 ppm, the shock didn’t reach breakpoint. Test again, recalculate and repeat.
- Swim only when free chlorine is back in the range the product label allows.
Worked example
An 18,000-gallon pool smells of chlorine. The test shows free chlorine 1.0 ppm and total chlorine 2.2 ppm.
- Combined chlorine = 2.2 − 1.0 = 1.2 ppm, well above 0.5, so it needs a shock.
- Breakpoint target = 10 × 1.2 = 12.0 ppm, so free chlorine has to rise by 11.0 ppm.
- Chlorine needed = 18,000 gal × 3.785 L × 11.0 mg/L = 750 g of chlorine.
| Product | Amount | Side effect |
|---|---|---|
| Liquid chlorine 12.5% | 1.7 gal (213 fl oz) | None that builds up |
| Cal-hypo 65% | 2.5 lb | +7.7 ppm calcium |
| Dichlor 56% | 3.0 lb | +9.9 ppm stabilizer (CYA) |
A single bag of shock (usually 1 lb) would have raised this pool by only about 4.3 ppm with 65% cal-hypo, well short of breakpoint. That is why “one bag per 10,000 gallons” so often fails. The dichlor row shows the other trap: shocking with it adds 10 ppm of stabilizer each time, and stabilizer only leaves when you drain water.
Shocking for algae is different
Algae needs chlorine held high for days, not a one-night shock. The high level has to be kept up until three things are true:
- the water is clear;
- combined chlorine is 0.5 ppm or less;
- the pool loses no more than 1 ppm of free chlorine overnight.
These are the criteria of the SLAM method used by the TroubleFreePool community. The overnight test catches algae you can’t see yet. How high to hold the chlorine depends on your stabilizer level. We don’t publish a single number for this until we have verified one, so use the CYA chart from that method or your chlorine product’s algae instructions.
Mistakes that waste shock
- Shocking with high pH. At pH 8, much less of your chlorine is in its strong form. Lower the pH first.
- Shocking in the sun. UV light destroys unstabilized chlorine within hours.
- Guessing the dose. Too little never reaches breakpoint. Too much wastes money and keeps swimmers out longer.
- Using stabilized shock every week. Dichlor and trichlor keep adding stabilizer, until chlorine stops working well.
Frequently asked questions
How often should I shock my pool?
Shock when your test results or the water tell you to, not on a fixed calendar. That means combined chlorine above about 0.5 ppm, a strong chlorine smell, cloudy water, algae, or after a heavy swim party or a big storm. A pool that holds steady free chlorine with no combined chlorine doesn’t need shocking.
Can I shock my pool during the day?
You can, but sunlight breaks chlorine down quickly, so part of the shock is wasted. Shocking at dusk lets the chlorine work all night.
Can I swim right after shocking?
No. Wait until free chlorine has dropped back to the level the product label allows for swimming, and retest before anyone gets in.
Is non-chlorine shock (potassium monopersulfate) enough?
Non-chlorine shock oxidises contaminants, but it does not sanitise the water and does not kill algae. It can help between chlorine shocks, but it is not a substitute when you have algae or the water is cloudy.
Sources
- Breakpoint chlorination: combined chlorine = total − free, target = 10 × combined chlorine (Indiana Department of Health, “How to shock the pool”).
- Free chlorine at least 1 ppm in pools and 3 ppm in hot tubs, and pH 7.0–7.8 (US CDC, home pool and hot tub water treatment and testing).
- Free chlorine pH of 7.0–7.4; low chlorine and high pH as causes of poor water quality (PWTAG Technical Note 34).
- Algae clean-up end-points: clear water, combined chlorine ≤ 0.5 ppm, overnight chlorine loss ≤ 1 ppm (TroubleFreePool, SLAM process and overnight chlorine loss test).
- Doses calculated with the same tested formulas as our shock calculator. 12.5% liquid chlorine checked against Orenda/PHTA’s 10.6 fl oz per ppm per 10,000 gallons.