Saltwater vs Chlorine Pool
The biggest myth about saltwater pools is in the name. A saltwater pool is a chlorine pool. The difference is where the chlorine comes from: a bottle you pour in, or a cell that makes it from salt. Once you see it that way, the real trade-offs are much easier to weigh.
How a salt system works
You dissolve ordinary pool salt (sodium chloride) in the water. As water flows through the salt cell, an electric current turns some of the dissolved chloride into chlorine, the same sanitiser you would otherwise buy. The chlorine does its job and eventually breaks back down to chloride, ready to go through the cell again. So the salt is mostly recycled, and you top it up only to replace water lost to splashing, backwashing and rain overflow.
How much salt it takes
Salt cells work in a narrow range set by the manufacturer. Hayward gives 2,700–3,400 ppm with 3,200 ppm as optimal for its AquaRite cells. Pentair’s figures vary by model, from 3,000–3,500 ppm to 3,600 ppm, so check the manual for your exact unit. For comparison, seawater holds about 35,000 ppm, more than ten times as much.
Start-up example: a new 15,000-gallon pool with no salt, aiming for 3,200 ppm, needs about 401 lb of salt. That’s 10 full 40-lb bags. Add it in stages and test before adding the last bag. Too much salt is only fixed by draining water. The salt calculator works it out for your pool and current salt level.
What you swap
With a traditional chlorine pool, you add chlorine by hand, often every day or two in summer. Say your 15,000-gallon pool uses 3 ppm of chlorine a day (real use varies with sun, swimmers and stabilizer). That’s about 48 fl oz of 12.5% liquid chlorine a day, or around 11.3 gallons a month to buy, carry and store. A salt cell makes that chlorine for you, steadily, whenever the pump runs.
What you take on instead: a cell that needs checking and cleaning when scale builds up, salt to test and top up, and a cell that eventually wears out and has to be replaced. Check the manufacturer’s expected life and warranty when you compare systems.
Side by side
| Traditional chlorine | Saltwater (chlorine generator) | |
|---|---|---|
| Sanitiser | Chlorine you add | Chlorine the cell makes |
| Daily work | Adding chlorine regularly | Mostly automatic; adjust the cell output |
| Up-front cost | Lower | Higher: cell and controller |
| Ongoing purchases | Chlorine, every week or so in season | Salt occasionally; a replacement cell eventually |
| pH | Depends on the chlorine product | Tends to drift up, so it needs acid often |
| Still need testing? | Yes: chlorine, pH, alkalinity, stabilizer | Yes: the same, plus salt |
The pH drift in salt pools
Almost every salt-pool owner notices pH creeping up, and adds acid more often than they used to. The cell’s chemistry and the gas bubbles it gives off both play a part; pool chemists still debate which matters more. The practical fix is the same either way: keep total alkalinity toward the lower end of the normal range, and lower pH with acid when it rises. Our guide on lowering alkalinity without crashing pH shows how, and the pH & alkalinity calculator gives the acid dose.
Which is right for you?
- Salt suits you if you want chlorine produced automatically, don’t want to haul and store chlorine, and are fine paying more up front and replacing the cell when it wears out.
- Traditional chlorine suits you if you want the lowest set-up cost, use the pool only part of the year, or have equipment or stone surfaces that aren’t rated for salt.
Either way, the water chemistry is the same: chlorine high enough to sanitise, pH in range, and regular testing. The chlorine calculator works for both.
Frequently asked questions
Is a saltwater pool chlorine-free?
No. A salt system is a chlorine generator: it turns dissolved salt into chlorine inside the cell. The water is sanitised by chlorine just like any other pool. What changes is that you no longer buy and pour chlorine yourself.
Does a saltwater pool taste salty?
Barely. At around 3,200 ppm, pool water has roughly a tenth of the salt in seawater (about 35,000 ppm). Most people can just taste it. Hayward warns that levels high enough to taste salty can also shut its cell down.
Can I convert my chlorine pool to salt?
Usually, yes. A salt system is added to the existing plumbing: a cell, a control box and the salt itself. Before converting, ask your pool builder or equipment makers whether your heater, pool surface, coping and fixtures are rated for salt water.
Do saltwater pools need other chemicals?
Yes. You still test and adjust pH, alkalinity and stabilizer, add salt to replace what is lost through splash-out, backwashing and draining, and shock when needed. Salt pools typically need acid regularly, because their pH tends to drift up.
Sources
- AquaRite ideal salt level 2,700–3,400 ppm, 3,200 ppm optimal, and high salt can shut the unit down and taste salty (Hayward, AquaRite owner’s manual).
- IntelliChlor salt recommendations of 3,000–3,500 ppm (IC15/IC20/IC40 manual) and 3,600 ppm (current Pentair product page and iChlor manual).
- Seawater salinity of about 35 parts per thousand, i.e. about 35,000 ppm (USGS, “Why is the ocean salty?”; NOAA JetStream, “Sea water”).
- Salt systems generate chlorine by electrolysis, and pH tends to rise in salt pools; the cause is debated (Orenda; TroubleFreePool).
- Salt and chlorine amounts calculated with the same tested formulas as our salt and chlorine calculators.