Home › Guides › Why Is My Pool Cloudy? Causes and Fixes

Why Is My Pool Cloudy? Causes and Fixes

Cloudy water is a symptom, not a problem in itself. Pouring in a clarifier without knowing why the water is cloudy treats the symptom and lets the cause come back. Work through these checks in order. Most cloudy pools are found out by the first two.

Safety first: if you can’t clearly see the floor of the deep end from the side, keep everyone out until it clears. UK pool guidance treats that as a reason to close a pool immediately.

The checklist, in order

What you see or testLikely causeFix
Free chlorine low, or combined chlorine above 0.5 ppmNot enough sanitiserShock to breakpoint
pH above 7.8, or alkalinity above 120 ppmScale forming in the water; chlorine weakenedLower pH / alkalinity
Hard water, or cloudy after cal-hypo shockCalcium coming out of solutionLower pH; partial drain and refill; switch to liquid chlorine
Chemistry fine, but the pump runs only a few hoursNot enough filteringRun the pump continuously until clear
Filter pressure high, or water goes cloudy right after cleaning the filterDirty or damaged filterClean or backwash; check grids, cartridges or sand
Green or dull tint, slippery walls, chlorine disappears overnightEarly algaeSustained high chlorine (see the shock guide)
Milky “bubbly” look that settles in a glassAir in the systemCheck the pump lid seal, the water level at the skimmer, and leaks on the suction side

1. Low chlorine: the usual suspect

Low free chlorine is the most common cause of cloudy water. Without enough sanitiser, bacteria and organic waste build up faster than the filter can remove them. Test free and total chlorine. If free chlorine is near zero, or combined chlorine (total minus free) is above about 0.5 ppm, shock the pool. Use the shock calculator to get the dose for your test results.

Ask why chlorine dropped, too. Heavy rain dilutes it, sunny days burn off unstabilized chlorine, and a busy weekend of swimmers uses it up.

2. High pH or alkalinity: scale you can’t see yet

When pH climbs above about 7.8, calcium carbonate starts to come out of solution as tiny particles. That is the same stuff that later forms scale on tiles. High pH also weakens chlorine, so problem 1 often follows. High alkalinity pushes pH up and keeps it there. Check pH and alkalinity, then use the pH & alkalinity calculator. If alkalinity is the real culprit, follow how to lower alkalinity without crashing pH.

3. Hard water

In areas with hard tap water, calcium builds up with every top-up, and every dose of cal-hypo shock adds more. Very hard water clouds easily whenever pH rises. A calcium hardness test tells you. The only real way to lower calcium is to replace some water with softer water. In the meantime, keeping pH in the low 7s and using liquid chlorine instead of cal-hypo helps.

4. Not enough filtering

A filter can only clean water that passes through it. If chemistry is fine but the water is dull, run the pump around the clock until it clears, then settle on a daily schedule long enough to keep it clear. Make sure return jets point to stir the water, so there are no dead spots.

5. A dirty or failing filter

Note your filter’s pressure gauge reading when it is clean. Many filter manufacturers suggest cleaning or backwashing when pressure rises about 8–10 psi above that baseline; check your filter’s manual. Also check:

6. Early algae

Before a pool turns green, algae often shows up as a dull, slightly hazy look, slippery walls, and chlorine that vanishes overnight. A one-off shock is usually not enough. Algae needs chlorine held high until the water is clear, combined chlorine is 0.5 ppm or less, and the pool loses no more than 1 ppm of chlorine overnight. The shock guide explains how.

7. Air in the water

Fine air bubbles make water look milky, especially near the return jets. Scoop a glass of pool water: if the haze settles and clears within a minute, it is air, not particles. Look for a loose pump lid, a cracked pump basket lid seal, a water level too low at the skimmer, or a leak on the suction side of the pump.

Clarifier or flocculant?

Only after the cause is fixed. A clarifier helps your filter catch very fine particles, and you keep filtering normally. A flocculant sinks particles to the floor for you to vacuum out to waste. It is faster, but more work. Neither one will hold back cloudiness caused by low chlorine or high pH.

Frequently asked questions

How long does it take for a cloudy pool to clear?

Once the cause is fixed, most pools clear in one to three days with the pump running continuously. Very fine particles can take longer, which is when a clarifier helps. If it is no better after three days of good chlorine and constant filtering, look again at the filter.

Should I use a clarifier or a flocculant?

A clarifier clumps tiny particles together so your filter can catch them. You keep filtering as normal, and it is the gentler choice for mild cloudiness. A flocculant drops particles to the floor as a layer you vacuum out to waste. It is faster for very cloudy water, but it is more work and you lose water. Neither fixes a chemistry problem, so fix chlorine and pH first.

Is it safe to swim in a cloudy pool?

No. If you can’t see the bottom of the deep end clearly, nobody can spot a swimmer in trouble, and UK public-pool guidance says a pool in that state should close. Cloudiness can also mean the water isn’t being sanitised properly.

Why did my pool go cloudy right after I shocked it?

Calcium-based shock (cal-hypo) can cloud water briefly, especially if your water is already hard or the pH is high. It usually clears within a day of filtering. If it happens every time, your calcium hardness is probably high, and liquid chlorine is a better choice for you.

Sources